What you will set up
A congress abstract usually names several authors, and one of them presents it. By the end of this article, an author who submits will add all the authors of the abstract, say who presents it, and put the authors in order. Only the presenting author will be asked to confirm and will appear as a speaker; the co-authors will be named on the abstract.
This takes three steps: allow several people per session, create the session roles, and tell each presentation type which roles it uses. Session Roles: Presenting Author, Co-Authors and Chairs explains every setting of a role in detail.
Step 1: Allow several people per session
- Open Content And Speakers, then Call for Content Settings, and its tab Speakers and messages.
- Tick Allow Multiple Speakers Per Session.
- Save.
Without this setting, authors cannot add anyone to their abstract, whatever the roles say.
Step 2: Create the role Presenting author
- Under Configure, open Session roles and choose Add new.
- Name the role "Presenting author".
- Tick Counts as a speaker: the presenting author appears in the speaker lists and has a speaker profile.
- Tick Must confirm the session: once the abstract is accepted, the presenting author is asked to confirm that they will present.
- Tick Submitters may take this role themselves: an author who will present can choose this role for themselves while submitting.
- Tick Session owners may add people in this role, so that an author who does not present can name the colleague who will.
- Set Display to Full: the public sees the presenting author as a speaker, with their profile.
- Tick Receives session mails, so the presenting author receives the decision mail.
- Save.
Step 3: Create the role Co-author
- Choose Add new again and name the role "Co-author".
- Leave Counts as a speaker and Must confirm the session cleared. Co-authors do not present, and they should not be asked to confirm.
- Tick Session owners may add people in this role. If you want each co-author to agree to being named, also tick Send them an invitation to accept: each co-author then receives an invitation and joins the abstract once they accept. Without it, co-authors are added at once.
- Tick Submitters may take this role themselves if an author who submits for a colleague should be able to name themselves as co-author.
- Set Display to Short: co-authors are listed on one line under the role's name, for example "Co-authors: Anna Müller (University of Vienna), Ben Schmidt".
- Save.
Good to know: Short names the co-authors on the public session page, on the agenda and in the Book of Abstracts alike. There is no setting that shows co-authors in the Book of Abstracts only. Hidden leaves them out everywhere, the Book of Abstracts included.
Step 4: Give each presentation type its roles
- Open Presentation Types, choose the presentation type, for example Oral presentation, and open its tab Roles.
- A new presentation type starts with the event's default role, Speaker. Choose Add role and add Presenting author, then Co-author.
- Set the limits. For Presenting author, enter 1 in Min and 1 in Max: every abstract has exactly one presenting author. For Co-author, enter a Max, for example 12, and leave Min empty.
- Choose Remove on Speaker, so that authors are not offered it.
- Save.
Repeat this for every presentation type with authors, for example Poster.
What the author sees
In the submission step for the people of the session, the author first chooses their own role: presenting author or co-author. Then they add each other author with their e-mail address and name, in the role that person plays. They can also choose from people they have worked with on earlier submissions, which saves typing. They can put the authors in order, because the order matters on the abstract.
If a change would break a limit, run.events refuses it with a sentence that names the rule, for example "Oral presentation allows at most 1 Presenting author." Only the person who submitted the session can add people to it.
Correcting the people of a session
As organizer, you can always change the people of a session, and your changes are not limited by Min and Max. Open the session, then its tab Edit, and the sub-tab Speakers. See Updating Speakers.
Common mistakes
- Authors cannot add anyone. Allow Multiple Speakers Per Session is not ticked.
- Authors are still offered the role Speaker. Remove Speaker on the presentation type's tab Roles.
- Co-authors are asked to confirm and appear as speakers. Clear Counts as a speaker and Must confirm the session on the role Co-author.
Related articles